Here down the page you'll find additional incredibly good expertise in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Setting up a bathtub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a new one is likewise a moderately difficult job. If the old tub is conveniently easily accessible, the project can relocate quickly; if you have to open a wall to remove the old tub as well as position the brand-new bath tub, the job is a lot harder. In either case, the job is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and set in the new one. Make certain you have certified yourself for the job and also are comfortable attempting it. As opposed to hiring a contractor to take over a halfway-completed task, it is much better to take into consideration utilizing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This short article will certainly assist you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and don't require to change the plan of your previous water system pipelines.
Your devices and also product checklist should make up the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the water system. After doing so, activate the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the restricted access that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the remaining water that will come from the pipes. When the supply pipes have been eliminated, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming during this procedure. Once the taps have been removed, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the tap and also the sink. Secure the tap in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap connectors. The previous type needs to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Utilizing both wooden boards under its feet, position the tub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the bath tub up until the spirit level reviews degree.
To set up taps, fit the bottom of the furthest flexible tap connector to the proper supply pipe by making a compression sign up with; then do the very same for the various other tap.
Switch on the water and also examine all joints as well as new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally check the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's user's manual. Tiling as well as securing around the bathtub must wait till the bath tub has been used a minimum of once as this will settle it right into its final placement.
Getting ready for the Setup
First of all, the sustaining frame supplied with the bathroom must be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the tub.
Fit the flexible faucet ports to the bottom of both taps utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its last setting.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to crack a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, leading to issues with dampness and also possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and also are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the tub with water before securing, to enable the motion experienced when the tub remains in use. The sealer can break relatively early if you do not think about this activity prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Post feedback down the page. We will be pleased to find out your thoughts about this blog entry. We hope that you come back again in the future. Sharing is caring. Helping others is fun. Many thanks for your time. Kindly check up our blog back soon.
Contact, be stress-free!